Riemen Belts
Transkript
Riemen Belts
Riemen Belts Lagerprogramm stock programme Sonderanfertigungen Auf Anfrage Zahnriemen/ -scheiben T2,5; T20; AT20; RPP3; MXL; XXH Supertorque; Poly-Chain. Alle Teilungen komplett gefertigt und konfektioniert nach Ihren Vorgaben. Zahnwellen T5; AT5; T10; AT10; L; H made to order on request belts/ pulleys T2,5; T20; AT20; RPP3; MXL; XXH supertorque; poly-chain. all pitches manufactured complete to your order racks T5; AT5; T10; AT10; L; H Unsere Konstrukteure beraten Sie gerne bei der Realisierung Ihrer Anwendung - Fordern Sie uns heraus! We offer more than competitive prices - contact our engineering department! Zahnriemen für die Antriebstechnik Timing Belts for Power Transmission Information Information Der synchrone Riemenantrieb stellt das modernste und weitverbreiteste Antriebssystem dar. Er ersetzt heute in zahlreichen Anwendungsbereichen die traditionellen Systeme mit Kettenantrieb oder Zahnradgetriebe. Die Evolution der Technik erfordert Systeme, welche immer höhere Leistungen bei geringeren Drehzahlen übertragen. Gleichzeitig ist es erforderlich, das Gewicht wie auch die räumlichen Abmessungen des Antriebs zu reduzieren. Dies bedeutet eine dynamische und besonders hohe Beanspruchung der Riemen, die auf Scheiben mit immer kleinerem Durchmesser arbeiten. The timing belt drive represents the most modern and efficient power transmission system and is replacing, in some applications, traditional roller chain and gear drivers. Technical evolution in power transmission design has required drives that can transmit increasingly higher power to weight ratio. This brings about high dynamic stress conditions which are the major cause of belt failures such as tooth jumping, tooth shear and noise. Forderungen nach Zuverlässigkeit, Betriebssicherheit, Geräuschreduzierung und höhere Zahnsprungsicherheit stehen dabei an erster Stelle. Dem Konstrukteur stehen zur Erfüllung dieser Anforderungen folgende Profile zur Verfügung: Das Trapezprofil Das Trapezprofil wird überwiegend in der Antriebstechnik eingesetzt und ist für leichte bis schwere Antriebe geeignet. Das Trapezprofil ist erhältlich in den Teilungen: T, AT, (metrisch), MXL, XL, L, H, XH, XXH, (zöllig), endlos, endlos mit großer Länge oder als Meterware. These failures are obviously unacceptable with the need to ensure the reliability, safety and noise-reduction criteria which the market now requires from modern drives. The Designer has the possibility to decide which profile to use. the trapezoidal profile The most common profile is the trapezoidal profile where low to medium power transmission is required. The trapezoidal profile is available in: T, AT, (metric), MXL, XL, L, H, XH, XXH, (inch), endless, endless welded, open length. Unsere Konstrukteure beraten Sie gerne bei der Realisierung Ihrer Anwendung - Fordern Sie uns heraus! We offer more than competitive prices - contact our engineering department! N1 Zahnriemen für die Antriebstechnik Timing Belts for Power Transmission Information Information Das HTD-Profil (high torque drive) therefore, we offer the HTD-profile HTD belts have a curvilinear tooth form giving a more uniform distribution of shear stresses within the teeth and a better transition of tooth loads to the tensile members in the belt. The HTD-profile is available in: HTD 3, HTD 5, HTD 8, HTD 14, endless, endless welded, open length. A further development is the RPP-profile RPP and HTD belts and pulleys are fully interchangeable. The RPP belt with the new parabolic profile has teeth thicker than in standard belts of comparable pitch; this characteristic and the „bulkiness“ of the teeth allow both an appreciable increase in power transmission as well as a reduction in interference between belt and pulley during mesh. The indentation at the top of the tooth results in an increased local elastic flexibility of the tooth during mesh. This permits: - easier air discharge; - reduced noise level; Dieses zeichnet sich durch eine bogenförmige Ausführung der Zahnflanken aus. Hierdurch wird eine gleichmäßige Spannungsverteilung im Riemenzahn erreicht und somit gleichförmige Lastübertragung vom Riemenzahn auf die Zugstränge. Die spezifische Belastung der einzelnen Zähne wird durch die größere Kontaktfläche geringer. Das HTD-Profil ist erhältlich in den Teilungen: HTD 3, HTD 5, HTD 8, HTD 14, endlos, endlos mit großer Länge und als Meterware. Eine weitere Entwicklung ist das RPP-Profil RPP und HTD Zahnriemen und Zahnriemenscheiben sind untereinander austauschbar. Der RPP Riemen mit dem neuen parabolischen Profil hat dickere Zähne als die Standardriemen vergleichbarer Teilung; diese Beschaffenheit und die „Form“ der Zähne ermöglichen eine beachtliche Erhöhung des Drehmoments sowie eine reduzierte Interferenz zwischen Zahnriemen und Zahnrad im Eingriff. Aus der Kerbung auf dem Zahnkopf resultiert eine höhere lokale elastische Verformung der Zähne in der Eingriffsphase. Dieses bietet folgende Vorteile: - leichteres Entweichen der Luft; - Interferenzminderung; N2 Zahnriemen für die Antriebstechnik Timing Belts for Power Transmission Information Information Das neue parabolische Zahnprofil und die verminderte Interferenz in der Eingriffsphase ermöglichen: - minimale Geräuschentwicklung; - maximale Sicherheit gegen Zahnübersprung; - erhöhte Leistungsübertragung; - optimale Verschleißbeständigkeit erhältlich in: 3 mm, 5 mm, 8 mm, 14 mm Teilung. RPP-Green Power The new parabolic tooth profile and the reduced interference during mesh allow: - reduced noise level; - greater resistance to tooth jump; - improved power capability; - improved shear stress resistance; available in: RPP 3; RPP 5; RPP 8 and RPP 14 RPP GREEN POWER Polyurethane parabolic timing belts The RPP polyurethane timing belt drive represent the most up to date and efficient power and linear transmission system. The profile is the same as RPP rubber construction and allows the belt to run on RPP pulleys. It is also possible to keep interchangeability with other drive systems available on the market. The RPP polyurethane GREEN POWER is available in: RPP 3, RPP 5, RPP 8 and RPP 14 with the following types: endless, endless long length andopen ended belts. RPP PLUS These belts are particularly recommended for high torque drives where: - an increase of up to 100 % in belt load can be achieved using the same sized pulleys as for RPP belts. Alternatively, a consequent reduction in pulley width can be obtained; Polyurethan Zahnriemen mit Parabolprofil Der RPP Polyurethan Zahnriementrieb stellt das modernste und effizienteste Linearkraftübertragungssystem dar. Er besitzt das gleiche Profil wie die RPP Gummikonstruktion und kann damit ebenfalls auf HTD-Scheiben eingesetzt werden. Außerdem ist eine Austauschbarkeit mit anderen auf dem Markt erhältlichen Übertragungssystemen möglich. Der RPP Polyurethan GREEN POWER ist erhältlich in: RPP 3, RPP 5, RPP 8 und RPP 14 in den folgenden Ausführungen: endlos, endlos mit großer Länge oder als Meterware. RPP Plus Diese Riemen sind besonders geeignet für Hochlastantriebe bei denen: - ein Anstieg bis zu 100 % der Riemenlast erreicht werden kann bei Weiterverwendung der gleichen Scheibengröße wie für RPP Riemen. Außerdem ist eine konsequente Reduktion des Scheibendurchmessers möglich; - the same pulleys used for RPP system, can be used maintaining functional interchangeability with other deep profile systems; - die gleichen Scheiben des RPP Systems benutzt werden können unter Beibehaltung der funktionalen Austauschbarkeit mit anderen Tiefenprofilen; - the life of existing systems can be improved without changing the pulleys; - die Lebensdauer von existierenden Systemen ohne Austausch der Scheiben erhöht werden; - noise can be reduced. Available in 8 and 14 mm pitch. - die Geräuschentwicklung reduziert werden kann. Erhältlich in 8 mm und 14 mm Teilung. Unsere Konstrukteure beraten Sie gerne bei der Realisierung Ihrer Anwendung - Fordern Sie uns heraus! We offer more than competitive prices - contact our engineering department! N3 Zahnriemen für die Antriebstechnik Timing Belts for Power Transmission Information Information *RPP PANTHER Der PANTHER verwendet das gleiche geräuscharme, parabolische Zahnprofil und dieselbe Kerbung, die bereits bei den RPP Riemen zu hoher Leistungsfähigkeit geführt haben; - die gleichen Scheiben des RPP Systems können unter Beibehaltung der funktionalen Austauschbarkeit mit anderen Tiefenprofilen bei Zahnscheiben mit bis zu 100 Zähnen benutzt werden; *RPP PANTHER The PANTHER uses the same quiet, parabolic tooth profile and tooth indentation which hasalready proved to be highly effective for RPP drive belts; - the same pulley used for the RPP system, can be used maintaining functional interchangeability with other deep profile systems up to 100 pulley teeth; - der RPP PANTHER erreicht einen Wirkungsgrad von annähernd 98 %; - erhöhte Leistungskapazität ermöglicht die Entwicklung kleinerer, kompakterer Antriebssysteme mit kleineren Scheibendurchmessern und reduzierten Zahnbreiten; - durch den präzise geschliffenen, weichen Neopren-Rücken ist der RPP PANTHER Riemen besonders geeignet für den Einsatz externer Spannrollen. Erhältlich in 8 mm und 14 mm Teilung. - the RPP PANTHER drive provides an operating efficiency of approximately 98 %; - increased power capacity allows to design smaller, more compact drives using smaller pulley diameters and reduced face widths; - the smooth, precision ground, neoprene rubber backing of RPP PANTHER belt ideally suitable to use an external idler. Available in 8 and 14 mm pitch. * Keine Lagerware; Preis und Lieferzeit auf Anfrage. *No stock items; please ask for price and delivery N4 RPP Parabolisches Profil RPP Parabolic Profile Profil | profile Teilung | pitch Standardbreiten [mm] standard widths [mm] Material | material type 320 480 536 560 600 632 640 680 720 800 840 880 920 960 1040 1080 1120 1200 1224 1280 1352 1440 1464 1600 1760 1800 2000 2400 2600 2800 3048 3280 3600 4400 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 RPP8 Länge/length [mm] Zähnez. No. teeth 320 480 536 560 600 632 640 680 720 800 840 880 920 960 1040 1080 1120 1200 1224 1280 1352 1440 1464 1600 1760 1800 2000 2400 2600 2800 3048 3280 3600 4400 40 60 67 70 75 79 80 85 90 100 105 110 115 120 130 135 140 150 153 160 169 180 183 200 220 225 250 300 325 350 381 410 450 550 type 966 1190 1400 1610 1764 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 RPP14 Zähnez. No. teeth 966 1190 1400 1610 1764 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956 69 85 100 115 126 127 135 150 165 175 185 200 225 240 250 275 309 327 354 Sonderlängen in verschweißter Auführung. Zugstrang in Stahl, Material Polyurethan Auf Anfrage erhältlich: Zahnriemen RPP mit Teilung 5M. Available on request: Timing belt RPP with pitch 5M. N5 Neopren | neoprene Länge/length [mm] Bestellbeispiel Länge Teilung Breite [mm] 920 8M 30 Auf Anfrage lieferbar: Zwischenbreite. Doppeltverzahnter Riemen. 8M, 14M 8, 14 mm 8M: 20, 30, 50, 85 14M: 40, 55, 85, 115, 170 example length pitch width [mm] 920 8M 30 available on request: other width. double sided belt. Special lengths welded, tension member steel, material polyurethane. RPP Plus für Hochlastenantrieb RPP Plus for High Torque Drives Profil | profile Teilung | pitch Standardbreiten [mm] standard widths [mm] 8M, 14M 8, 14 mm 8M: 20, 30, 50, 85 14M: 40, 55, 85, 115, 170 Material | material type 288 320 352 384 408 480 536 544 560 600 632 640 680 720 800 840 880 920 960 1040 1080 1120 1200 1224 1280 1352 1440 1464 1600 1760 1800 2000 2400 2600 2800 3048 3280 3600 4400 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 PLUS 8 Länge/length [mm] Zähnez. No. teeth 288 320 352 384 408 480 536 544 560 600 632 640 680 720 800 840 880 920 960 1040 1080 1120 1200 1224 1280 1352 1440 1464 1600 1760 1800 2000 2400 2600 2800 3048 3280 3600 4400 36 40 44 48 51 60 67 68 70 75 79 80 85 90 100 105 110 115 120 130 135 140 150 153 160 169 180 183 200 220 225 250 300 325 350 381 410 450 550 type 966 1092 1190 1400 1610 1764 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 PLUS 14 Neopren | neoprene Länge/length [mm] Zähnez. No. teeth 966 1092 1190 1400 1610 1764 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956 69 78 85 100 115 126 127 135 150 165 175 185 200 225 240 250 275 309 327 354 Bestellbeispiel Länge Teilung Breite [mm] 1140 8MPlus 30 Auf Anfrage lieferbar: Zwischenbreite. Doppeltverzahnter Riemen. Sonderlängen in verschweißter Auführung. Zugstrang in Stahl, Material Polyurethan example length pitch width [mm] 1140 8MPlus 30 available on request: other width. double sided belt. Special lengths welded, tension member steel, material polyurethane. N6 Polyurethan-Zahnriemen Polyurethane-Timing Belts Profil | profile Teilung | pitch Standardbreiten [mm] standard widths [mm] T5 5 mm 10, 16, 25 Material | material Zugstrang | tension member type * T5 T5 T5 T5 T5 * T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 T5 * T5 T5 T5 T5 T5 T5 T5 T5 T5 * T5 T5 T5 T5 T5 T5 T5 * T5 T5 T5 T5 T5 - N7 120 150 165 185 200 210 215 220 225 245 250 255 260 270 275 280 295 300 305 325 330 340 350 355 360 365 375 390 400 410 420 425 440 445 450 455 460 475 480 500 510 525 545 550 560 Länge/length [mm] Zähnez. No. teeth 120 150 165 185 200 210 215 220 225 245 250 255 260 270 275 280 295 300 305 325 330 340 350 355 360 365 375 390 400 410 420 425 440 445 450 455 460 475 480 500 510 525 545 550 560 24 30 33 37 40 42 43 44 45 49 50 51 52 54 55 56 59 60 61 65 66 68 70 71 72 73 75 78 80 82 84 85 88 89 90 91 92 95 96 100 102 105 109 110 112 type T5 T5 T5 T5 T5 * T5 T5 T5 T5 * T5 T5 T5 T5 T5 T5 T5 T5 T5 * T5 T5 T5 * T5 * T5 T5 T5 * T5 T5 T5 T5 * T5 T5 * T5 * T5 * T5 * T5 T5 * T5 * T5 * T5 * T5 * T5 T5 T5 * T5 - 575 590 600 610 620 625 630 650 660 675 690 700 720 725 750 780 800 815 830 840 850 860 885 900 940 975 990 1000 1075 1090 1100 1115 1140 1160 1200 1215 1275 1280 1315 1350 1355 1380 1440 1955 Polyurethan | polyurethane Stahl | steel Länge/length [mm] Zähnez. No. teeth 575 590 600 610 620 625 630 650 660 675 690 700 720 725 750 780 800 815 830 840 850 860 885 900 940 975 990 1000 1075 1090 1100 1115 1140 1160 1200 1215 1275 1280 1315 1350 1355 1380 1440 1955 115 118 120 122 124 125 126 130 132 135 138 140 144 145 150 156 160 163 166 168 170 172 177 180 188 195 198 200 215 218 220 223 228 232 240 243 255 256 263 270 271 276 288 391 Polyurethan-Zahnriemen Polyurethane-Timing Belts Profil | profile Teilung | pitch Standardbreiten [mm] standard widths [mm] AT5 5 mm 10, 16, 25 Material | material Zugstrang | tension member type * AT5 * AT5 * AT5 AT5 * AT5 AT5 AT5 AT5 AT5 * AT5 AT5 * AT5 * AT5 * AT5 * AT5 * AT5 * AT5 * AT5 * AT5 * AT5 AT5 AT5 AT5 * AT5 * AT5 * AT5 - 225 255 280 300 340 375 390 420 450 455 500 545 600 610 660 710 720 750 780 825 860 975 1050 1125 1500 2000 Länge/length [mm] Zähnez. No. teeth 225 255 280 300 340 375 390 420 450 455 500 545 600 610 660 710 720 750 780 825 860 975 1050 1125 1500 2000 45 51 56 60 68 75 78 84 90 91 100 109 120 122 132 142 144 150 156 165 172 195 210 225 300 400 Bestellbeispiel Breite [mm] Teilung Länge 16 AT5 500 Auf Anfrage lieferbar: Zwischenbreite. Doppeltverzahnter Riemen. Sonderlängen in verschweißter Auführung, oder endlos gewickelt, Zugstrang in Kevlar. * Kein Lagerbestand - separat anfragen. * non stock item - please ask for delivery Polyurethan | polyurethane Stahl | steel example width [mm] pitch length 16 AT5 500 available on request: other width. double sided belt. Special lengths welded, or as endless belt, tension member kevlar. N8 Polyurethan-Zahnriemen Polyurethane-Timing Belts Profil | profile Teilung | pitch Standardbreiten [mm] standard widths [mm] Material | material Zugstrang | tension member type T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 * T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 - N9 370 400 410 440 450 500 530 550 560 600 610 630 650 660 690 700 720 730 750 780 800 810 840 850 880 890 900 910 920 950 960 970 980 Länge/length [mm] Zähnez. No. teeth 370 400 410 440 450 500 530 550 560 600 610 630 650 660 690 700 720 730 750 780 800 810 840 850 880 890 900 910 920 950 960 970 980 37 40 41 44 45 50 53 55 56 60 61 63 65 66 69 70 72 73 75 78 80 81 84 85 88 89 90 91 92 95 96 97 98 type * T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 * T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 T 10 - 1000 1010 1050 1080 1100 1110 1140 1150 1200 1210 1240 1250 1300 1320 1350 1390 1400 1420 1440 1450 1460 1500 1560 1600 1610 1700 1750 1780 1800 1880 1960 2250 T10 10 mm 16, 25, 32,50 Polyurethan | polyurethane Stahl | steel Länge/length [mm] Zähnez. No. teeth 1000 1010 1050 1080 1100 1110 1140 1150 1200 1210 1240 1250 1300 1320 1350 1390 1400 1420 1440 1450 1460 1500 1560 1600 1610 1700 1750 1780 1800 1880 1960 2250 100 101 105 108 110 111 114 115 120 121 124 125 130 132 135 139 140 142 144 145 146 150 156 160 161 170 175 178 180 188 196 225 Polyurethan-Zahnriemen Polyurethane-Timing Belts Profil | profile Teilung | pitch Standardbreiten [mm] standard widths [mm] AT10 10 mm 16, 25, 32, 50 Material | material Zugstrang | tension member type * AT 10 * AT 10 * AT 10 AT 10 AT 10 AT 10 AT 10 AT 10 AT 10 AT 10 AT 10 * AT 10 * AT 10 AT 10 * AT 10 AT 10 AT 10 AT 10 AT 10 AT 10 - 500 560 600 610 660 700 730 780 800 840 890 920 960 980 1000 1010 1050 1080 1100 1150 Länge/length [mm] Zähnez. No. teeth 500 560 600 610 660 700 730 780 800 840 890 920 960 980 1000 1010 1050 1080 1100 1150 50 56 60 61 66 70 73 78 80 84 89 92 96 98 100 101 105 108 110 115 type * AT 10 * AT 10 * AT 10 AT 10 * AT 10 AT 10 * AT 10 AT 10 AT 10 * AT 10 AT 10 * AT 10 AT 10 * AT 10 * AT 10 * AT 10 * AT 10 AT 10 - 1200 1210 1250 1280 1300 1320 1350 1360 1400 1420 1480 1500 1600 1700 1720 1800 1860 1940 Polyurethan | polyurethane Stahl | steel Länge/length [mm] Zähnez. No. teeth 1200 1210 1250 1280 1300 1320 1350 1360 1400 1420 1480 1500 1600 1700 1720 1800 1860 1940 120 121 125 128 130 132 135 136 140 142 148 150 160 170 172 180 186 194 Bestellbeispiel Breite [mm] Teilung Länge 16 AT10 500 Auf Anfrage lieferbar: Zwischenbreite. Doppeltverzahnter Riemen. Sonderlängen in verschweißter Auführung, oder endlos gewickelt, Zugstrang in Kevlar. * Kein Lagerbestand - separat anfragen. * non stock item - please ask for delivery example width [mm] pitch length 16 AT10 500 available on request: other width. double sided belt. Special lengths welded, or as endless belt, tension member kevlar. N 10 Neopren-Zahnriemen Neoprene-Timing Belts Profil | profile Teilung [mm] | pitch [inch] Standardbreiten [mm] XL 5,080 mm | 1/5“ 9,4 - 12,7 - 19,05 - 25,4 38,1 - 50,8 - 76,2 0,37“ - 0,5“ - 0,75“ 1“ - 1,5“ - 2“ - 3“ standard widths [inch] Material | material Zugstrang | tension member type 100 102 106 110 120 130 140 150 156 160 170 180 182 190 198 200 202 210 212 214 220 228 230 234 N 11 XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL Länge/length [mm] Zähnez. No. teeth 254,00 259,08 269,24 279,40 304,80 330,20 355,60 381,00 396,24 406,40 431,80 457,20 462,28 482,60 502,92 508,00 513,08 533,40 538,48 543,56 558,80 579,12 584,20 594,36 50 51 53 55 60 65 70 75 78 80 85 90 91 95 99 100 101 105 106 107 110 114 115 117 type 240 250 260 270 276 290 310 316 320 330 344 352 364 380 384 390 392 434 530 600 710 XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL Neopren | neoprene Glasfaser | glass cord Länge/length [mm] Zähnez. No. teeth 609,60 635,00 660,40 685,80 701,04 736,60 787,40 838,20 873,76 894,08 924,56 894,08 924,56 965,20 975,36 990,60 995,68 1102,36 1346,20 1524,00 1803,40 120 125 130 135 138 145 155 165 172 176 182 176 182 190 192 195 196 217 265 300 355 Neopren-Zahnriemen Neoprene-Timing Belts Profil | profile Teilung [mm] | pitch [inch] Standardbreiten [mm] L 9,525 mm | 3/8“ 12,7 - 19,05 - 25,4 38,1 - 50,8 - 76,2 0,5“ - 0,75“ - 1“ 1,5“ - 2“ - 3“ standard widths [inch] Material | material Zugstrang | tension member type 124 135 150 173 187 202 210 225 240 255 270 285 300 322 345 367 390 405 412 420 450 480 510 540 600 728 817 L L L L L L L L L L L L L L L L L L L L L L L L L L L Länge/length [mm] Zähnez. No. teeth 314,33 342,90 381,00 438,15 476,25 514,35 533,40 571,50 609,60 647,70 685,80 723,90 762,00 819,15 876,30 933,45 990,60 1028,70 1047,75 1066,80 1143,00 1219,20 1295,40 1371,60 1524,00 1847,85 2076,45 33 36 40 46 50 54 56 60 64 68 72 76 80 86 92 98 104 108 110 112 120 128 136 144 160 194 218 Bestellbeispiel Bezeichnung Teilung Breite [Zoll] 600 L 1“ Auf Anfrage lieferbar: Zwischenbreite. Doppeltverzahnter Riemen. Sonderlängen in verschweißter Auführung. Zugstrang in Stahl, Material Polyurethan Neopren | neoprene Glasfaser | glass cord example type pitch width [mm] 600 L 1“ available on request: other width. double sided belt. Special lengths welded, tension member steel, material polyurethane. N 12 Neopren-Zahnriemen Neoprene-Timing Belts Profil | profile Teilung [mm] | pitch [inch] Standardbreiten [mm] H 12,7 mm | 1/2“ 12,7 - 19,05 - 25,4 38,1 - 50,8 - 76,2 0,5“ - 0,75“ - 1“ 1,5“ - 2“ - 3“ standard widths [inch] Material | material Zugstrang | tension member type 240 255 270 300 330 360 390 420 450 480 510 540 570 600 H H H H H H H H H H H H H H Länge/length [mm] Zähnez. No. teeth 609,60 647,70 685,80 762,00 838,20 914,40 990,60 1066,80 1143,00 1219,20 1295,40 1371,60 1447,80 1524,00 48 51 54 60 66 72 78 84 90 96 102 108 114 120 type 630 660 700 725 750 800 850 900 1000 1100 1120 1140 1150 1250 1400 1700 H H H H H H H H H H H H H H H H Bestellbeispiel Bezeichnung Teilung Breite [Zoll] 240 H 1“ Auf Anfrage lieferbar: Zwischenbreite. Doppeltverzahnter Riemen. Sonderlängen in verschweißter Auführung. Zugstrang in Stahl, Material Polyurethan N 13 Neopren | neoprene Glasfaser | glass cord Länge/length [mm] Zähnez. No. teeth 1600,20 1676,40 1778,00 1841,50 1905,00 2032,00 2159,00 2286,00 2540,00 2794,00 2844,80 2895,60 2921,00 3175,00 3556,00 4318,00 126 132 140 145 150 160 170 180 200 220 224 228 230 250 280 340 example type pitch width [mm] 240 H 1“ available on request: other width. double sided belt. Special lengths welded, tension member steel, material polyurethane. Zahnriemen Meterware - Polyurethan Polyurethane Open End -Timing Belts Profil | profile Rollenlänge | rollength T-Profile 50 m Profil T5 p = 5 mm | pitch Stahlzugstrang Kevlarzugstrang Stahl-PAZ Kevlar-PAZ Stahl-PAZ/PAR Kevlar-PAZ/PAR profile T5 Riemenbreiten | width 10 16 25 32 50 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 75 100 X X X X X X Profil T10 p = 10 mm | pitch profile T10 Riemenbreiten | width 10 Stahlzugstrang Kevlarzugstrang Stahl-PAZ Kevlar-PAZ Stahl-PAZ/PAR Kevlar-PAZ/PAR 16 25 32 50 75 100 150 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Profil T20 p = 20 mm | pitch profile T20 Riemenbreiten | width 10 Stahlzugstrang Stahl-PAZ 150 16 25 32 50 75 100 150 X X X X X X X X X X X X „X“ = Standard - andere Breiten auf Anfrage erhältlich. „X“ = standard - other width available on request N 14 Zahnriemen Meterware - Polyurethan Polyurethane Open End -Timing Belts Profil | profile Rollenlänge | rollength AT-Profile 50 m Profil AT5 p = 5 mm | pitch Stahlzugstrang Stahl-PAZ profile AT5 Riemenbreiten | width 10 16 25 32 50 X X X X X X X X X X 75 100 150 Profil AT10 p = 10 mm | pitch profile AT10 Riemenbreiten | width 10 Stahlzugstrang Stahl-PAZ 16 25 32 50 75 100 150 X X X X X X X X X X X X X X Profil AT20 p = 20 mm | pitch profile AT20 Riemenbreiten | width 10 16 25 32 50 75 100 X X X X X X X X X X Stahlzugstrang Stahl-PAZ 150 HTD-Profile | HTD-profile Profil 5M p = 5 mm | pitch Stahlzugstrang Stahl-PAZ profile 5M Riemenbreiten | width 10 15 X X X X 20 25 30 50 75 100 X X Profil 8M p = 8 mm | pitch profile 8M Riemenbreiten | width 10 15 20 25 30 50 75 100 X X X X X X X X X X X X Stahlzugstrang Stahl-PAZ Profil 14M p = 14 mm | pitch N 15 115 profile 14M Riemenbreiten | width 10 Stahlzugstrang Stahl-PAZ 115 15 20 25 30 50 75 100 115 X X X X X X X X X X X X Zahnriemen Meterware - Polyurethan Polyurethane Open End -Timing Belts Zöllige Profile | inch profile Rollenlänge | rollength 50 m Profil XL - 5,08 mm p = 0,2 Zoll | pitch mm Code / inch Stahlzugstrang Stahl-PAZ Kevlar-PAZ profile XL - 5,08 mm Riemenbreiten | width 9,53 037 12,7 050 19,05 075 25,4 100 X X X X X X X X X X X X 38,1 150 50,8 200 76,2 300 profile L - 9,53 mm Riemenbreiten | width 9,53 037 Stahlzugstrang Stahl-PAZ Kevlar-PAZ 12,7 050 19,05 075 25,4 100 X X X X X X X X X 38,1 150 50,8 200 76,2 300 Riemenbreiten | width 9,53 037 12,7 050 19,05 075 25,4 100 X X X X X X 38,1 150 50,8 200 76,2 300 102 400 X X X 152,4 600 X X X Profil XH - 22,23 mm Stahlzugstrang Stahl-PAZ Kevlar-PAZ 152,4 600 profile H - 12,7 mm Stahlzugstrang Stahl-PAZ Kevlar-PAZ p = 0,875 Zoll | pitch mm Code / inch 102 400 X X X Profil H - 12,7 mm p = 0,5 Zoll | pitch mm Code / inch 152,4 600 X X X Profil L - 9,53 mm p = 0,375 Zoll | pitch mm Code / inch 102 400 profile H - 22,23 mm Riemenbreiten | width 9,53 037 12,7 050 19,05 075 25,4 100 X X X „X“ = Standard - andere Breiten auf Anfrage erhältlich. „X“ = standard - other width available on request 38,1 150 50,8 200 76,2 300 102 400 X X X X X X X X X 152,4 600 N 16 Zahnriemen Meterware Neopren Neoprene Open End Timing Belts Profil | profile Rollenlänge | rollength RPP 50 m Profil RPP 5 p = 5 mm | pitch Glasfaserzugstrang profile RPP 5 Riemenbreiten | width 9 12 15 20 25 X X X X X 50 100 X Profil RPP 8 p = 8 mm | pitch profile RPP 8 Riemenbreiten | width 9 12 Glasfaserzugstrang 15 20 25 X X X 50 100 Zöllige Profile | inch-profile Profil XL - 5,08 mm p = 0,2 Zoll | pitch mm Code / inch Glasfaserzugstrang profile XL - 5,08 mm Riemenbreiten | width 6,35 025 7,87 031 9,53 037 12,7 050 X X X X 19,05 075 25,4 100 X Profil L - 9,53 mm p = 0,375 Zoll | pitch mm Code / inch profile L - 9,53 mm Riemenbreiten | width 6,35 025 7,87 031 9,53 037 Glasfaserzugstrang 12,7 050 19,05 075 25,4 100 X X X Profil H - 12,7 mm p = 0,5 Zoll | pitch mm Code / inch Glasfaserzugstrang profile H - 12,7 mm Riemenbreiten | width 6,35 025 7,87 031 9,53 037 12,7 050 19,05 075 25,4 100 X X X „X“ = Standard - andere Breiten auf Anfrage erhältlich. „X“ = standard - other width available on request N 17 Zahnriemenbeschichtungen Belts Backing´s Gebrauchsbezeichnung description Linatex Porol Schaumvulkollan Supergrip PAZ Linatex Porol PU Foam Supergrip NT base material natural rubber cellular rubber PVC polyamid Grundmaterial Naturkautschuk Zellkautschuk polyurethane foam geschäumtes Polyurethan PVC Polyamid colour Farbe red rot black schwarz yellow/brown gelblich-braun blue/green blau-grün mit Waffelmuster hardness Härte approx. 40° shore A ca. 40° Shore A approx. 15° shore A ca. 15° Shore A approx. 40° shore A ca. 40° Shore A approx. 30° shore A ca. 30° Shore A available thicknesses 1,6; 2,4; 3,2; 5,0; 8,0; 10,0; 15,0; 20,0 mm & combinations 1,6; 2,4; 3,2; 5,0; 8,0; 10,0; 15,0; 20,0 mm Kombinationen möglich 2,0; 3,0; 5,0 mm & combinations 2,0; 3,0; 5,0 mm & combinations 4,0 mm lengths over 3 m will have multiple joins Längen ab 3 m werden auf Stoß zusammengesetzt lengths over 3 m will have multiple joins Längen ab 3 m werden auf Stoß zusammengesetzt lengths over 3 m will have multiple joins Längen ab 3 m werden auf Stoß zusammengesetzt low abrasion resistance high friction coefficient bedingt abriebfest zähelastisch, hoher Reibwert not abrasion resistance high friction coefficient großer Abrieb, hoher Reibwert good abrasion resistance high friction coefficient gute Abriebfestigkeit hoher Reibwert limitet wear resistance high friction coefficient bedingt verschleißfest, hoher Reibwert application areas tractor haul-offs & all glass & paper transport drives incline industry technische Verwendung Kabelzugmaschinen, allgem. Transportanlagen all types of light types of light transport drives allgem. Transportzwecke leichter Art Glasindustrie Papierindustrie gut geeignet für Schrägförderung Lieferbare Dicken maximum length max. Längen technical properties technische Eigenschaften green grün 2,0; 3,0; 5,0 mm 2,0; 3,0; 5,0 mm 4,0 mm Kombinationen möglich Kombinationen möglich low coefficient of friction geringer Reibwert erleichtert Zahneingriff vermindert Geräusche conveyors unterstützte Transportzahnriemen N 18 Zahnriemenbeschichtungen Belts Backing´s Gebrauchsbezeichnung description Friktionsbelag mit weißen Noppen HV1-Folie Gummi Correx beige PU 06 PAR friction backing HV1 Strip correx rubber PU 06 NB base material Grundmaterial PVC PVC polyurethane Polyurethan artificial rubber Para-Gummi polyurethane foam Polyurethan colour Farbe white weiß transparent transparent beige beige yellow gelb hardness Härte approx. 40° Shore A ca. 40° Shore A approx. 80° Shore A ca. 80° Shore A approx. 35-40° Shore A approx. 60° Shore A ca. 35-40° Shore A ca. 60° Shore A available thicknesses Lieferbare Dicken 2,4 mm 1,0 mm 6,0; 10,0 mm 2,4 mm 1,0 mm 6,0; 10,0 mm maximum length lengths over 3 m will have multiple joins Längen ab 3 m werden auf Stoß zusammengesetzt 10 m lengths over 5 m will have multiple joins Längen ab 5 m werden auf Stoß zusammengesetzt lengths over 1,2 m will have multiple joins Längen ab 1,2 m werden auf Stoß zusammengesetzt low abrasion resistance high friction coefficient bedingt verschleißfest, hoher Reibwert good abrasion resistance good abrasion resistance high grip good abrasion resistance gute Abriebfestigkeit abriebfeste Qualität, gute Mitnahme gute Abriebfestigkeit application areas technische Verwendung incline conveyors food industry gut geeignet für Schrägförderung Lebensmittelindustrie food industry general conveying allgemeine Transportanlagen general conveying allgemeine Transportanlagen Bestellbeispiel: ordering example: Synchroflex-Zahnriemen 32 AT 5/ 825 mit 2,4 mm Linatex-Beschichtung Synchroflex Timing Belts 32 AT 5/ 825 with 2,4 mm Linatex backing max. Längen technical properties technische Eigenschaften N 19 10 m Lebensmittelindustrie polyamid Polyamid green grün 2,0; 3,0; 4,0; 5,0 mm & combinations 2,0; 3,0; 4,0; 5,0 mm Kombinationen möglich geringer Reibwert gleitfreudig und verschleißfest leichte Stauförderer Standard-Zahnriemenscheiben Standard-Timing Belt Pulleys vorgebohrt | pilot bored T-Profile 50 m zentriert | centered Typenübersicht different types of belt pulleys * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. N 20 Standard HTD-Zahnriemenscheiben Standard HTD-Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered HTD 5M 5 mm Lieferbar auf Anfrage. Available on your request. Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab HTD 8M 8 mm Z = 38 Stahl Z = 40 Grauguß material up to no. of teeth from Z = 38 steel Z = 40 cast iron Für Zahnriemenbreite 20 mm Zähnezahl No. teeth 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 d 56,02 61,12 66,21 71,30 76,39 81,49 86,58 91,67 96,77 101,86 112,05 122,23 142,60 162,97 183,35 203,72 229,18 285,21 366,69 427,81 488,92 for belt width 20 mm do da dn b l db* type** 54,65 59,75 64,84 70,08 75,13 80,16 85,22 90,30 95,39 100,49 110,67 120,86 141,23 161,60 181,97 202,35 227,81 283,83 365,32 426,44 487,55 60,00 66,00 71,00 75,00 83,00 87,00 91,00 98,50 103,00 106,00 119,00 127,00 148,00 168,00 192,00 - 43 45 50 50 55 60 70 70 75 75 75 75 80 80 80 90 90 90 90 100 100 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 12 12 12 15 15 15 15 15 15 15 15 15 15 15 15 15 15 18 20 20 20 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6WF 6WF 6WF 6A 6A 6A 6A 6A 6A Für Zahnriemenbreite 30 mm Zähnezahl No. teeth 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 N 21 d 56,02 61,12 66,21 71,30 76,39 81,49 86,58 91,67 96,77 101,86 112,05 122,23 142,60 162,97 183,35 203,72 229,18 285,21 366,69 427,81 488,92 Bestell-Nr. Part No. 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 -8M-20 for belt width 30 mm do da 54,65 59,75 64,84 70,08 75,13 80,16 85,22 90,30 95,39 100,49 110,67 120,86 141,23 161,60 181,97 202,35 227,81 283,83 365,32 426,44 487,55 60,00 66,00 71,00 75,00 83,00 87,00 91,00 98,50 103,00 106,00 119,00 127,00 148,00 168,00 192,00 - ** Type siehe Seite N 20 ** type look at page N 20 dn b l db* type** 43 45 50 50 55 60 70 70 75 75 75 75 90 90 95 100 100 100 100 100 100 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 12 12 12 15 15 15 15 15 15 15 15 15 15 15 15 15 15 18 20 20 20 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6WF 6WF 6WF 6A 6A 6A 6A 6A 6A Bestell-Nr. Part No. 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 -8M-30 Standard HTD-Zahnriemenscheiben Standard HTD-Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab HTD 8M 8 mm Z = 38 Stahl Z = 40 Grauguß material up to no. of teeth from Z = 38 steel Z = 40 cast iron Für Zahnriemenbreite 50 mm Zähnezahl No. teeth 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 d 56,02 61,12 66,21 71,30 76,39 81,49 86,58 91,67 96,77 101,86 112,05 122,23 142,60 162,97 183,35 203,72 229,18 285,21 366,69 427,81 488,92 for belt width 50 mm do da dn b l db* type** 54,65 59,75 64,84 70,08 75,13 80,16 85,22 90,30 95,39 100,49 110,67 120,86 141,23 161,60 181,97 202,35 227,81 283,83 365,32 426,44 487,55 60,00 66,00 71,00 75,00 83,00 87,00 91,00 98,50 103,00 106,00 119,00 127,00 148,00 168,00 192,00 - 43 45 50 50 55 60 70 70 75 75 75 80 90 100 100 110 110 110 110 120 130 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 70 70 70 70 70 70 70 70 70 70 70 70 60 60 60 60 60 60 60 60 60 12 12 12 15 15 15 15 15 15 18 18 18 18 18 18 18 18 18 20 20 20 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 10WF 10WF 10WF 10A 10A 10A 10A 10A 10A Für Zahnriemenbreite 85 mm Zähnezahl No. teeth 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 d 56,02 61,12 66,21 71,30 76,39 81,49 86,58 91,67 96,77 101,86 112,05 122,23 142,60 162,97 183,35 203,72 229,18 285,21 366,69 427,81 488,92 Bestell-Nr. Part No. 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 -8M-50 for belt width 85 mm do da 54,65 59,75 64,84 70,08 75,13 80,16 85,22 90,30 95,39 100,49 110,67 120,86 141,23 161,60 181,97 202,35 227,81 283,83 365,32 426,44 487,55 60,00 66,00 71,00 75,00 83,00 87,00 91,00 98,50 103,00 106,00 119,00 127,00 148,00 168,00 192,00 - ** Type siehe Seite N 20 ** type look at page N 20 dn b l db* type** 43 45 50 50 55 60 70 70 75 75 75 80 80 100 110 110 110 110 120 120 130 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 105 105 105 105 105 105 105 105 105 105 105 105 105 95 95 95 95 95 95 95 95 12 12 12 15 15 15 15 15 15 18 18 18 20 20 20 20 20 24 24 24 24 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 10WF 10WF 10A 10A 10A 10A 10A 10A Bestell-Nr. Part No. 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 -8M-85 N 22 Standard HTD-Zahnriemenscheiben Standard HTD-Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered HTD 14M 14 mm Material material Grauguß cast iron Für Zahnriemenbreite 40 mm Zähnezahl No. teeth 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 d 124,78 129,23 133,69 142,60 151,52 160,43 169,34 178,25 196,08 213,90 249,55 285,21 320,86 356,51 401,07 499,11 641,71 748,66 855,62 962,57 for belt width 40 mm do da 122,12 126,57 130,99 139,88 148,79 157,68 166,60 175,49 193,28 211,11 246,76 282,41 318,06 353,71 398,28 496,32 638,92 745,87 852,82 959,76 127,00 138,00 138,00 154,00 160,00 168,00 183,00 188,00 211,00 226,00 256,00 296,00 - dn b l db* type** 100 100 100 100 100 100 120 120 120 135 135 135 135 135 135 135 135 135 135 150 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 69 69 69 69 69 69 69 69 69 69 69 69 69 69 69 69 69 69 69 69 24 24 24 24 24 24 24 24 24 24 28 28 28 28 28 28 28 28 28 28 6F 6F 6F 6F 6F 6F 6F 6F 6F 6WF 6WF 6WF 6A 6A 6A 6A 6A 6A 6A 6A Für Zahnriemenbreite 55 mm Zähnezahl No. teeth 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 N 23 d 124,78 129,23 133,69 142,60 151,52 160,43 169,34 178,25 196,08 213,90 249,55 285,21 320,86 356,51 401,07 499,11 641,71 748,66 855,62 962,57 Bestell-Nr. Part No. 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 -14M-40 for belt width 55 mm do da 122,12 126,57 130,99 139,88 148,79 157,68 166,60 175,49 193,28 211,11 246,76 282,41 318,06 353,71 398,28 496,32 638,92 745,87 852,82 959,76 127,00 138,00 138,00 154,00 160,00 168,00 183,00 188,00 211,00 226,00 256,00 296,00 - ** Type siehe Seite N 20 ** type look at page N 20 dn b l db* type** 100 100 100 100 100 100 120 120 120 135 135 135 135 135 135 135 135 135 135 150 70 70 70 70 70 70 70 70 70 70 70 70 70 70 70 70 70 70 70 70 85 85 85 85 85 85 85 85 85 70 70 70 70 70 70 70 70 70 70 70 24 24 24 24 24 24 24 24 24 24 28 28 28 28 28 28 28 28 28 28 6F 6F 6F 6F 6F 6F 6F 6F 6F 10WF 10WF 10WF 10A 10A 10A 10A 10A 10A 10A 10A Bestell-Nr. Part No. 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 -14M-55 Standard HTD-Zahnriemenscheiben Standard HTD-Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered HTD 14M 14 mm Material material Grauguß cast iron Für Zahnriemenbreite 85 mm Zähnezahl No. teeth 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 d 124,78 129,23 133,69 142,60 151,52 160,43 169,34 178,25 196,08 213,90 249,55 285,21 320,86 356,51 401,07 499,11 641,71 748,66 855,62 962,57 for belt width 85 mm do da 122,12 126,57 130,99 139,88 148,79 157,68 166,60 175,49 193,28 211,11 246,76 282,41 318,06 353,71 398,28 496,32 638,92 745,87 852,82 959,76 127,00 138,00 138,00 154,00 160,00 168,00 183,00 188,00 211,00 226,00 256,00 296,00 - dn b l db* type** 100 100 100 100 100 100 120 135 135 150 150 150 150 150 150 150 150 150 165 165 102 102 102 102 102 102 102 102 102 102 102 102 102 102 102 102 102 102 102 102 117 117 117 117 117 117 117 117 117 117 102 102 102 102 102 102 102 102 102 102 24 24 24 24 24 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 10WF 10WF 10A 10A 10A 10A 10A 10A 10A 10A Für Zahnriemenbreite 115 mm Zähnezahl No. teeth 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 d 124,78 129,23 133,69 142,60 151,52 160,43 169,34 178,25 196,08 213,90 249,55 285,21 320,86 356,51 401,07 499,11 641,71 748,66 855,62 962,57 Bestell-Nr. Part No. 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 -14M-85 for belt width 115 mm do da 122,12 126,57 130,99 139,88 148,79 157,68 166,60 175,49 193,28 211,11 246,76 282,41 318,06 353,71 398,28 496,32 638,92 745,87 852,82 959,76 127,00 138,00 138,00 154,00 160,00 168,00 183,00 188,00 211,00 226,00 256,00 296,00 - ** Type siehe Seite N 20 ** type look at page N 20 dn b l db* type** 100 100 100 100 100 120 120 135 140 150 150 150 150 150 150 150 165 165 165 165 133 133 133 133 133 133 133 133 133 133 133 133 133 133 133 133 133 133 133 133 148 148 148 148 148 148 148 148 148 148 148 133 133 133 133 133 133 133 133 133 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 10WF 10A 10A 10A 10A 10A 10A 10A 10A Bestell-Nr. Part No. 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 -14M-115 N 24 Standard HTD-Zahnriemenscheiben Standard HTD-Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered HTD 14M 14 mm Material material Grauguß cast iron Für Zahnriemenbreite 170 mm Zähnezahl No. teeth 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 d 124,78 129,23 133,69 142,60 151,52 160,43 169,34 178,25 196,08 213,90 249,55 285,21 320,86 356,51 401,07 499,11 641,71 748,66 855,62 962,57 for belt width 170 mm do da 122,12 126,57 130,99 139,88 148,79 157,68 166,60 175,49 193,28 211,11 246,76 282,41 318,06 353,71 398,28 496,32 638,92 745,87 852,82 959,76 127,00 138,00 138,00 154,00 160,00 168,00 183,00 188,00 211,00 226,00 256,00 296,00 - dn b l db* type** 100 100 100 100 100 120 135 140 160 160 160 180 180 180 180 200 220 220 220 220 187 187 187 187 187 187 187 187 187 187 187 187 187 187 187 187 187 187 187 187 202 202 202 202 202 202 202 202 202 202 202 202 187 187 187 187 187 187 187 187 32 32 32 32 32 32 32 32 32 32 32 32 32 32 38 38 38 38 38 38 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 10WF 10WF 10A 10A 10A 10A 10A 10A Bestellbeispiel Mat. Zähnezahl Teilung Riemenbreite St. 25 5 M 15 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. N 25 ** Type siehe Seite N 20 ** type look at page N 20 Bestell-Nr. Part No. 28 29 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 168 192 216 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 -14M-170 example mat. no. teeth pitch belt width St. 25 5 M 15 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. Standard Zahnriemenscheiben Standard Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab XL 5,080 mm | 1/5“ mm Z = 30 Stahl Z = 32 Aluminium material up to no. of teeth from Für Zahnriemenbreite 0,37“ (9,53 mm) Zähnezahl No. teeth 10 11 12 14 15 16 18 20 21 22 24 26 28 30 32 36 40 42 44 48 60 72 d 16,17 17,79 19,40 22,64 24,26 25,87 29,11 32,34 33,96 35,57 38,81 42,04 45,28 48,51 51,74 58,21 64,68 67,91 71,15 77,62 97,02 116,43 do 15,66 17,28 18,90 22,13 23,75 25,36 28,60 31,83 33,45 35,07 38,30 41,53 44,77 48,00 51,24 57,70 64,17 67,41 70,64 77,11 96,51 115,92 Z = 30 steel Z = 32 aluminium for belt width 0,37“ (9,53 mm) da 23,00 23,00 25,00 28,00 28,00 32,00 36,00 38,00 38,00 42,00 44,00 48,00 51,00 54,00 - dn b l db* type** 9,50 9,50 12,70 14,30 15,90 17,50 19,00 23,80 23,80 25,40 27,00 30,00 30,20 34,90 38,00 38,00 38,00 38,00 38,00 38,00 38,00 38,00 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 14,3 19,8 19,8 19,8 19,8 19,8 19,8 19,8 22,2 22,2 22,2 22,2 22,2 22,2 22,2 25,4 25,4 25,4 25,4 25,4 25,4 25,4 25,4 5 5 5 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6 6 6 6W 6W 6W 6W 6W Bestellbeispiel Mat. Zähnezahl Teilung Riemenbreite St. 30 XL 037 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. ** Type siehe Seite N 20 ** type look at page N 20 Bestell-Nr. Part No. 10 11 12 14 15 16 18 20 21 22 24 26 28 30 32 36 40 42 44 48 60 72 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 -XL-037 example mat. no. teeth pitch belt width St. 30 XL 037 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. N 26 Standard Zahnriemenscheiben Standard Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab L 9,525 mm | 3/8“ mm Z = 32 Stahl Z = 36 Grauguß material up to no. of teeth from Für Zahnriemenbreite 0,5“ (12,7 mm) Zähnezahl No. teeth 10 12 13 14 15 16 17 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 d 30,32 36,38 39,41 42,45 45,48 48,51 51,54 54,57 57,61 60,64 63,67 66,70 72,77 78,83 84,89 90,96 97,02 109,15 121,28 133,40 145,53 181,91 218,30 254,68 do 29,59 35,62 38,65 41,68 44,72 47,75 50,78 53,81 56,84 59,88 62,91 65,94 72,00 78,07 84,13 90,20 96,26 108,39 120,51 132,64 144,77 181,15 217,53 253,92 for belt width 0,5“ (12,7 mm) da 36 42 44 48 51 54 57 60 60 66 71 75 79 87 91 97 103 115 127 140 152 - dn b l db* type** 22 28 30 33 36 38 40 40 40 46 46 50 50 50 50 50 50 50 50 50 50 50 50 50 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 28 28 28 6 6 6 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 15 15 15 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6WF 6WF 6AF 6AF 6A 6A 6A * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. N 27 Z = 32 steel Z = 36 cast iron ** Type siehe Seite N 20 ** type look at page N 20 Bestell-Nr. Part No. 10 12 13 14 15 16 17 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 -L-050 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. Standard Zahnriemenscheiben Standard Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab L 9,525 mm | 3/8“ mm Z = 32 Stahl Z = 36 Grauguß material up to no. of teeth from Für Zahnriemenbreite 0,75“ (19,05 mm) Zähnezahl No. teeth 10 12 13 14 15 16 17 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 d 30,32 36,38 39,41 42,45 45,48 48,51 51,54 54,57 57,61 60,64 63,67 66,70 72,77 78,83 84,89 90,96 97,02 109,15 121,28 133,40 145,53 181,91 218,30 254,68 do 29,59 35,62 38,65 41,68 44,72 47,75 50,78 53,81 56,84 59,88 62,91 65,94 72,00 78,07 84,13 90,20 96,26 108,39 120,51 132,64 144,77 181,15 217,53 253,92 Z = 32 steel Z = 36 cast iron for belt width 0,75“ (19,05 mm) da 36 42 44 48 51 54 57 60 60 66 71 75 79 87 91 97 103 115 127 140 152 - dn b l db* type** 22 28 30 33 36 38 40 40 40 46 46 50 50 50 50 50 50 55 60 60 60 60 60 60 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 26 26 29 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 35 35 35 6 8 8 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 15 15 15 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6WF 6WF 6AF 6AF 6A 6A 6A Bestellbeispiel Mat. Zähnezahl Teilung Riemenbreite St. 60 L 075 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. ** Type siehe Seite N 20 ** type look at page N 20 Bestell-Nr. Part No. 10 12 13 14 15 16 17 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 -L-075 example mat. no. teeth pitch belt width St. 60 L 075 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. N 28 Standard Zahnriemenscheiben Standard Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab L 9,525 mm | 3/8“ mm Z = 32 Stahl Z = 36 Grauguß material up to no. of teeth from Für Zahnriemenbreite 1“ (25,4 mm) Zähnezahl No. teeth 10 12 13 14 15 16 17 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 d 30,32 36,38 39,41 42,45 45,48 48,51 51,54 54,57 57,61 60,64 63,67 66,70 72,77 78,83 84,89 90,96 97,02 109,15 121,28 133,40 145,53 181,91 218,30 254,68 do 29,59 35,62 38,65 41,68 44,72 47,75 50,78 53,81 56,84 59,88 62,91 65,94 72,00 78,07 84,13 90,20 96,26 108,39 120,51 132,64 144,77 181,15 217,53 253,92 for belt width 1“ (25,4 mm) da 36 42 44 48 51 54 57 60 60 66 71 75 79 87 91 97 103 115 127 140 152 - dn b E l db* 22 28 30 33 36 38 40 40 40 46 46 50 50 50 50 50 50 55 60 60 60 60 60 60 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 32 32 32 32 32 32 32 6 6 - 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 32 32 35 35 35 6 8 8 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 15 15 15 Bestellbeispiel Mat. Zähnezahl Teilung Riemenbreite St. 60 L 100 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. N 29 Z = 32 steel Z = 36 cast iron ** Type siehe Seite N 20 ** type look at page N 20 type** 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6CWF 6CWF 10AF 10AF 6A 6A 6A Bestell-Nr. Part No. 10 12 13 14 15 16 17 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 -L-100 example mat. no. teeth pitch belt width St. 60 L 100 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. Standard Zahnriemenscheiben Standard Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab H 12,7 mm | 1/2“ mm Z = 48 Stahl Z = 56 Grauguß material up to no. of teeth from Für Zahnriemenbreite 0,75“ (19,05 mm) Zähnezahl No. teeth 14 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 d 56,60 64,68 72,77 76,81 80,85 84,89 88,94 97,02 105,11 113,19 121,28 129,36 145,53 161,70 177,87 194,04 do 55,22 63,31 71,39 75,44 79,48 83,52 87,56 95,65 103,73 111,82 119,90 127,99 144,16 160,33 176,50 192,67 da 64,00 70,00 79,00 82,50 87,00 91,00 94,00 102,00 112,00 120,00 128,00 135,00 152,00 168,00 184,00 200,00 Z = 48 steel Z = 56 cast iron for belt width 0,75“ (19,05 mm) dn b 40 46 54 58 62 67 70 75 80 80 80 70 80 80 80 90 26,4 26,4 26,4 26,4 26,4 26,4 26,4 26,4 26,4 26,4 26,4 27,0 26,4 26,4 26,4 26,4 E l db* 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 10 10 12 12 12 12 12 12 15 15 15 15 20 20 20 20 Für Zahnriemenbreite 1“ (25,4 mm) Zähnezahl No. teeth 14 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 96 120 d 56,60 64,68 72,77 76,81 80,85 84,89 88,94 97,02 105,11 113,19 121,28 129,36 145,53 161,70 177,87 194,04 242,55 291,06 339,57 388,08 485,10 do 55,22 63,31 71,39 75,44 79,48 83,52 87,56 95,65 103,73 111,82 119,90 127,99 144,16 160,33 176,50 192,67 241,18 289,69 338,20 386,71 483,73 type** 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6AF 6AF Bestell-Nr. Part No. 14 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 -H-075 for belt width 1“ (25,4 mm) da 63,00 71,00 79,00 82,00 87,00 91,00 93,00 103,00 111,00 119,00 127,00 135,00 152,00 168,00 184,00 200,00 - dn b E l db* 40 46 54 58 62 67 70 75 55 60 60 70 80 80 80 80 80 80 80 80 90 31 31 31 31 31 31 31 31 32 32 32 32 32 32 32 32 34 34 34 34 34 8 8 8 - 41 41 41 41 41 41 41 41 32 32 32 40 40 40 40 40 45 45 45 45 50 10 10 12 12 12 12 12 12 15 15 15 20 20 20 20 20 20 20 20 20 20 ** Type siehe Seite N 20 ** type look at page N 20 type** 6F 6F 6F 6F 6F 6F 6F 6F 6CWF 6CWF 6CWF 6WF 6WF 6AF 6AF 6AF 6A 6A 6A 6A 6A Bestell-Nr. Part No. 14 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 96 120 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 -H-100 N 30 Standard Zahnriemenscheiben Standard Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab H 12,7 mm | 1/2“ mm Z = 48 Stahl Z = 56 Grauguß material up to no. of teeth from Für Zahnriemenbreite 1,5“ (38,1 mm) Zähnezahl No. teeth 14 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 96 120 d 56,60 64,68 72,77 76,81 80,85 84,89 88,94 97,02 105,11 113,19 121,28 129,36 145,53 161,70 177,87 194,04 242,55 291,06 339,57 388,08 485,10 do 55,22 63,31 71,39 75,44 79,48 83,52 87,56 95,65 103,73 111,82 119,90 127,99 144,16 160,33 176,50 192,67 241,18 289,69 338,20 386,71 483,73 for belt width 1,5“ (38,1 mm) da 63,00 71,00 79,00 82,00 87,00 91,00 93,00 103,00 111,00 119,00 127,00 135,00 152,00 168,00 184,00 200,00 - dn b E l db* 40 46 54 58 62 67 70 75 55 60 60 70 80 80 80 80 85 85 85 85 95 44 44 44 44 44 44 44 44 45 45 45 45 45 45 45 45 46 46 46 46 46 18 18 18 8 8 - 54 54 54 54 54 54 54 54 35 35 35 45 45 55 12 12 12 12 12 12 12 12 15 15 15 20 20 20 20 20 20 20 20 20 24 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. N 31 Z = 48 steel Z = 56 cast iron ** Type siehe Seite N 20 ** type look at page N 20 type** 6F 6F 6F 6F 6F 6F 6F 6F 6CWF 6CWF 6CWF 6CWF 6CWF 10AF 10AF 10AF 10A 10A 10A 10A 6A Bestell-Nr. Part No. 14 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 96 120 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 -H-150 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. Standard Zahnriemenscheiben Standard Timing Belt Pulleys Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material bis Zähnezahl ab H 12,7 mm | 1/2“ mm Z = 48 Stahl Z = 56 Grauguß material up to no. of teeth from Für Zahnriemenbreite 2“ (50,8 mm) Zähnezahl No. teeth 14 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 96 120 d 56,60 64,68 72,77 76,81 80,85 84,89 88,94 97,02 105,11 113,19 121,28 129,36 145,53 161,70 177,87 194,04 242,55 291,06 339,57 388,08 485,10 do 55,22 63,31 71,39 75,44 79,48 83,52 87,56 95,65 103,73 111,82 119,90 127,99 144,16 160,33 176,50 192,67 241,18 289,69 338,20 386,71 483,73 for belt width 2“ (50,8 mm) da 63,00 71,00 79,00 82,00 87,00 91,00 93,00 103,00 111,00 119,00 127,00 135,00 152,00 168,00 184,00 200,00 - dn b E l db* 40 46 54 58 62 67 70 75 60 60 70 70 80 80 80 85 90 90 90 90 100 58 58 58 58 58 58 58 58 58 58 58 58 58 58 58 58 60 60 60 60 60 24 24 24 19 19 - 68 68 68 68 68 68 68 68 42 42 42 47 47 45 45 45 50 50 50 50 - 12 15 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20 20 20 24 Für Zahnriemenbreite 3“ (76,2 mm) Zähnezahl No. teeth 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 96 120 d 64,68 72,77 76,81 80,85 84,89 88,94 97,02 105,11 113,19 121,28 129,36 145,53 161,70 177,87 194,04 242,55 291,06 339,57 388,08 485,10 do 63,31 71,39 75,44 79,48 83,52 87,56 95,65 103,73 111,82 119,90 127,99 144,16 160,33 176,50 192,67 241,18 289,69 338,20 386,71 483,73 Z = 48 steel Z = 56 cast iron type** 6F 6F 6F 6F 6F 6F 6F 6F 6CWF 6CWF 6CWF 6CWF 6CWF 11AF 11AF 11AF 11A 11A 11A 11A 11A Bestell-Nr. Part No. 14 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 96 120 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 -H-200 for belt width 3“ (76,2 mm) da 71,00 79,00 82,00 87,00 91,00 93,00 103,00 111,00 119,00 127,00 135,00 152,00 168,00 184,00 200,00 - dn b E l db* 46 54 58 62 67 70 75 60 60 70 70 80 80 80 85 100 100 100 100 110 84 84 84 84 84 84 84 84 84 84 84 84 84 84 84 86 86 86 86 86 35 35 35 35 35 - 94 94 94 94 94 94 94 57 57 57 57 57 55 55 55 55 55 55 55 65 15 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20 20 20 24 type** 6F 6F 6F 6F 6F 6F 6F 6CWF 6CWF 6CWF 6CWF 6CWF 11AF 11AF 11AF 11A 11A 11A 11A 11A Bestell-Nr. Part No. 16 18 19 20 21 22 24 26 28 30 32 36 40 44 48 60 72 84 96 120 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 -H-300 N 32 Standard Zahnriemenscheiben metrisch Standard Timing Belt Pulleys Metric Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material | material T5 5 mm Aluminium | aluminium Zahnscheibenbreite I pulley width I Verzahnungsbreite b tooth width b 21 - 27 - 36 15 - 21 - 30 Für Zahnriemenbreite 10, 16, 25 mm Zähnezahl No. teeth 10 12 14 15 16 18 19 20 22 24 25 26 27 28 30 32 36 40 42 44 48 60 d 15,91 19,10 22,28 23,87 25,47 28,65 30,24 31,83 35,01 38,19 39,79 41,38 42,97 44,56 47,75 50,93 57,30 63,66 66,85 70,03 76,39 95,49 do 15,05 18,25 21,45 23,05 24,60 27,80 29,40 31,00 34,25 37,40 39,00 40,60 42,20 43,75 46,95 50,10 56,45 62,85 66,00 69,20 75,55 94,65 for belt width 10, 16, 25 mm da 19,5 23 25 28 32 32 36 36 38 42 44 44 48 48 51 54 63 67 71 - dn db* type** 8 10 13 16 18 19 22 23 24 26 26 26 30 32 34 38 38 40 40 45 50 65 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8 8 8 8 8 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6 6 6 Bestell-Nr. Part No. *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ *..T5/ * Hier bitte Zahnscheibenbreite eingeben *here the pulley width code giving in Bestellbeispiel Mat. Zahnscheibenbreite Teilung Zähnezahl Al 21 T 5 20 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. N 33 ** Type siehe Seite N 20 ** type look at page N 20 example mat. pulley width pitch no. teeth Al 21 T 5 20 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. 10 12 14 15 16 18 19 20 22 24 25 26 27 28 30 32 36 40 42 44 48 60 Standard Zahnriemenscheiben metrisch Standard Timing Belt Pulleys Metric Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material | material AT5 5 mm Aluminium | aluminium Zahnscheibenbreite I pulley width I Verzahnungsbreite b tooth width b 21 - 27 - 36 15 - 21 - 30 Für Zahnriemenbreite 10, 16, 25 mm Zähnezahl No. teeth 10 12 14 15 16 18 19 20 22 24 25 26 27 28 30 32 36 40 42 44 48 60 d 15,91 19,10 22,28 23,87 25,47 28,65 30,24 31,83 35,01 38,19 39,79 41,38 42,97 44,56 47,75 50,93 57,30 63,66 66,85 70,03 76,39 95,49 do 14,65 17,85 21,05 22,65 24,20 27,40 29,00 30,60 33,85 37,00 38,60 40,20 41,80 43,35 46,55 49,70 56,05 62,45 65,60 68,80 75,15 94,25 for belt width 10, 16, 25 mm da 19,5 23 25 28 32 32 36 36 38 42 44 44 48 48 51 54 63 67 71 - dn db* type** 8 10 13 16 18 19 22 23 24 26 26 26 30 32 34 38 38 40 40 45 50 65 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8 8 8 8 8 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6 6 6 Bestell-Nr. Part No. *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ *..AT5/ 10 12 14 15 16 18 19 20 22 24 25 26 27 28 30 32 36 40 42 44 48 60 * Hier bitte Zahnscheibenbreite eingeben *here the pulley width code giving in Bestellbeispiel Mat. Zahnscheibenbreite Teilung Zähnezahl Al 21 AT 5 20 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. ** Type siehe Seite N 20 ** type look at page N 20 example mat. pulley width pitch no. teeth Al 21 AT 5 20 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. N 34 Standard Zahnriemenscheiben metrisch Standard Timing Belt Pulleys Metric Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material | material T10 10 mm Aluminium | aluminium Zahnscheibenbreite I pulley width I bis | to z = 16: 31 - 40 ab | from z = 18: 31 - 40 - 47 - 66 Verzahnungsbreite b tooth width b 21 - 30 - 37 - 56 Für Zahnriemenbreite 16, 25, 32, 50 mm Zähnezahl No. teeth 12 14 15 16 18 19 20 22 24 25 26 27 28 30 32 36 40 44 48 60 d 38,19 44,56 47,74 50,93 57,29 60,47 63,66 70,02 76,39 79,57 82,76 85,94 89,12 95,49 101,85 114,59 127,32 140,05 152,78 190,98 do 36,35 42,70 45,90 49,05 55,45 58,60 61,80 68,15 74,55 77,70 80,90 84,10 87,25 93,65 100,00 112,75 125,45 138,20 150,95 189,10 for belt width 16, 25, 32, 50 mm da 42 48 51 54 60 66 66 75 83 83 87 91 93 97 106 119 131 - dn db* type** 28 32 32 35 40 44 46 52 58 60 60 60 60 60 65 70 80 88 95 110 6 8 8 8 10 10 12 12 12 12 12 12 12 12 12 16 16 16 16 16 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6 6 6 Bestell-Nr. Part No. *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ *..T10/ * Hier bitte Zahnscheibenbreite eingeben *here the pulley width code giving in Bestellbeispiel Mat. Zahnscheibenbreite Teilung Zähnezahl Al 31 T 10 20 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. N 35 ** Type siehe Seite N 20 ** type look at page N 20 example mat. pulley width pitch no. teeth Al 31 T 10 20 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. 12 14 15 16 18 19 20 22 24 25 26 27 28 30 32 36 40 44 48 60 Standard Zahnriemenscheiben metrisch Standard Timing Belt Pulleys Metric Profil | profile Teilung | pitch Vorgebohrt/ Zentriert pilot bored/ centered Material | material AT10 10 mm Aluminium | aluminium Zahnscheibenbreite I pulley width I bis | to z = 16: 31 - 40 ab | from z = 18: 31 - 40 - 47 - 66 Verzahnungsbreite b tooth width b 21 - 30 - 37 - 56 Für Zahnriemenbreite 16, 25, 32, 50 mm Zähnezahl No. teeth 12 14 15 16 18 19 20 22 24 25 26 27 28 30 32 36 40 44 48 60 d 38,19 44,56 47,74 50,93 57,29 60,47 63,66 70,02 76,39 79,57 82,76 85,94 89,12 95,49 101,85 114,59 127,32 140,05 152,78 190,98 do 36,35 42,70 45,90 49,05 55,45 58,60 61,80 68,15 74,55 77,70 80,90 84,10 87,25 93,65 100,00 112,75 125,45 138,20 150,95 189,10 for belt width 16, 25, 32, 50 mm da 42 48 51 54 60 66 66 75 83 83 87 91 93 97 106 119 131 - dn db* type** 28 32 32 35 40 44 46 52 58 60 60 60 60 60 65 70 80 88 95 110 6 8 8 8 10 10 12 12 12 12 12 12 12 12 12 16 16 16 16 16 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6F 6 6 6 Bestell-Nr. Part No. *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ *..AT10/ 12 14 15 16 18 19 20 22 24 25 26 27 28 30 32 36 40 44 48 60 * Hier bitte Zahnscheibenbreite eingeben *here the pulley width code giving in Bestellbeispiel Mat. Zahnscheibenbreite Teilung Zähnezahl Al 31 AT 10 20 * Wir behalten uns vor, die Teile statt der Vorbohrung nur beidseitig zentriert zu liefern. ** Type siehe Seite N 20 ** type look at page N 20 example mat. pulley width pitch no. teeth Al 31 AT 10 20 * Parts maybe supplied with Pilot bore stated in the above table or solid bore with centre. N 36 Standard Zahnriemenscheiben mit Klemmbuchsen Standard Timing Belt Pulleys with taper-bush N 37 Profile HTD 5M, 8M, 14M Profile HTD 5M, 8M, 14M L L H H Lieferbar auf Anfrage. Available on our request. Klemmplatten Clamping Belt Plates Riemenbreite | belt width RB Material | material T5 + AT5 T10 + AT10 5 M HTD 8 M HTD 14 M HTD Aluminium | aluminium RB C A B D S F 10 16 25 16 25 32 50 10 15 25 20 30 50 85 40 55 85 115 170 29 35 44 41 50 57 75 28 34 44 45 55 75 110 71 86 116 146 201 41,8 41,8 41,8 80 80 80 80 41,8 41,8 41,8 66 66 66 66 116 116 116 116 116 3,2 3,2 3,2 5 5 5 5 3,2 3,2 3,2 5 5 5 5 9 9 9 9 9 5,5 5,5 5,5 9 9 9 9 5,5 5,5 5,5 9 9 9 9 11 11 11 11 11 8 8 8 15 15 15 15 8 8 8 15 15 15 15 22 22 22 22 22 6 6 6 8 8 8 8 6 6 6 8 8 8 8 10 10 10 10 10 Riemenspanner & Spannrollen Belt Tensioner & Tensioning Roller Für Zahnriementriebe Fs[N] smax (bei Pos.1) 000000- 80 135 350 800 1500 2600 40 50 50 65 87,5 112,5 for timing belt drives max. Drehzahl max.r.p.m. A B C dn E G H J1 J2 K [kg] Bestell-Nr Part No. 8000 8000 8000 6000 5000 4500 30 40 40 60 80 90 35 45 45 60 90 135 7 11 12 15 18 22 35 45 58 78 95 115 51 64 78 107 140 200 5 5 6 7 10 12 M6 M8 M10 M12 M16 M20 80 100 100 130 175 225 60 80 80 100 140 180 20 25 30 50 60 70 0,25 0,60 0,80 2,15 4,75 8,30 381-035-001 381-045-002 381-045-003 381-060-009 381-090-014 381-135-023 Montageanleitung siehe Seiten M 15 & M 16 mounting instruction: please look at pages M 15 & M 16 Spannrolle tensioning roller max. Drehzahl max.r.p.m. A B L M 8000 8000 30 40 35 45 2 6 14 16 Nmax 5 7 O M8 M10 [kg] Bestell-Nr Part No. 0,08 0,17 381-035-030 381-045-040 N 38 Notizen | Notice