İçi Dolu Aks Mobil Ultrasonik Muayene Sistemi - Epsilon-NDT
Transkript
İçi Dolu Aks Mobil Ultrasonik Muayene Sistemi - Epsilon-NDT
SAT –Dolu Aks Testi SAT – Solid Axle Testing Trenlerdeki dolu aksların testi için kullanılabilecek bir mobil sistem. A mobile system for the testing of solid axles on the train. Mobil dolu aks test cihazı, dolu aksların mekanize edilmiş ultrasonik test işlemi için tasarlanmıştır. Testin amacı, tekerlek grubu aksındaki enine uzanan çatlakların tespitidir. Aks üzerindeki kesit değişim yerleri, özellikle aks ve tekerlek arasındaki geçiş bölgesi çatlamaya karşı görece çok daha zayıftır. Tüm bunlara ek olarak, dolu aksın toplam hacmi de test edilmektedir. The mobile solid shaft test equipment is designed for the mechanized ultrasonic testing of built-in wheels (solid shaft). Ambition of the test is the detection of transverse cracks in the wheelset axle. The areas of the cross-section transitions are considered as threatened to crack easily, especially the changeover from the wheel receiver to the shaft. In addition, the total volume of the solid shaft is tested. Test modülü adaptörü ve aks bağlantısında, arama ünitesinin radyal olarak dönmesine olanak sağlayan bir adet döner tahrik motoru vardır. Ünitelerin bağlantıları yağ ile sağlanmaktadır. Ultrasonik sinyallare üniteden cihaza kontak halka vericisi aracılığı ile iletilmektedir. Çevresel pozisyon, açı vericisi ile algılanmaktadır. Kamalı (2°- 8°) dikey arama üniteleri 2-4 MHz test frekansı aralığında kullanılmaktadır. Test süresi boyunca, test üniteleri dalganın ön ucunda sabit rotasyon ile hareket ettirilirler ve ultrasonik sinyaller doğrudan bu rotasyon hareketinin yönü ve açısına bağlı olarak kaydedilir. Uzun süreli veri saklama imkanı için; test edilen dalganın bilgisi, test parametreleri ve test sonuçları gibi yapılan teste ilişkin her türlü bilgi bir veritabanına kaydedilir ve burada depolanır. Kaydedilen bütün bilgiler daha sonra istendiğinde görüntülenebilir, analiz edilebilir ya da işlenebilir. There is a rotary drive on the connection of the test module adapter and shaft, which lets the search units rotate radially. The coupling of the units is done with oil. The ultrasonic signals are transmitted via slip ring transmitter from the unit to the device. The peripheral position is detected by an angle transmitter. Perpendicular search units with a wedge (2° - 8°) are used with a test frequency of 2-4 MHz. During the test, the test units are moved with constant rotation at the front end of the wave and the ultrasonic signals are stored exactly with regard to their ways and angles. For the long-term data retention, all relevant information about performed tests, such as data of the tested wave, test parameters and test results are stored in a database. All stored data can be viewed, analyzed and processed afterwards. 7 Özellikler Chraracteristics Hareketlilik Kompakt ve dayanıklı yapı Tanınmış üreticilerden sağlanan kalitesi ispatlanmış parçalar Düşük bakım ihtiyacı ve yüksek dayanıklılık Kullanımı kolay Farklı dolu akslara monte işleminin sağlanması için adaptör Trenlerde kullanılan her tip dolu aksın testi Delik çapı 30 mm ve 90 mm olan aksların testi Hızlı test Sonuçların analizi, geometrik tabanlı hızlı veri analizi Test sonuçlarının dökümantasyonu İyi tanımlanmış test dizileri sayesinde daha iyi bir kalite güvencesi Mobility Compact and robust construction Proven components from reputable manufacturers Low maintenance and high durability Easy to use Adapter to attach different types of solid shafts Testing of all types of solid axels on trains Shaft with drill diameters of 30 mm and 90 mm can be tested Rapid testing Analysis of results, fast geometry-based data analysis Documentation of test results Further quality assurance through welldefined test sequences 8 Modüler Tasarım Modular Design Yaklaşım cihazı (mekanik elemanlar ve bağlantı araçları) Ultrasonik Test Sistemi Veri toplama ve analiz Panel Test sonuçlarını görüntüleyebilmek ve kayıt altında tutabilmek için veri bankası Advancing device (mechanical components and coupling medium) Ultrasonic Test System Data collection and analysis Panel Database for archiving and displaying test results Teknik Parametreler Technical Parameters Cihaz EN 12668 Standardlarına uygundur Aks başından ultrasonik muayene yapılması mümkündür. Kompakt ve portatif Endüstriyel PC, endüstriyel dokunmatik TFT ekran ve endüdstriyel klavye Gelişmiş güç yönetimi Aynı anda 8 algılayıcıdan(prob) veri alarak ölçüm yapabilme imkanı Kesin konumlama için hareketli ve esnek algılayıcı tutucusu Algılayıcı tutucuları kolayca ve hızlıca farklı aks tiplerine uyarlanabilir Her algılayıcının aks başı etrafında 360° dairesel olarak dönebilme kabiliyeti Dahili koordinat arayüzü Maksimum 5 dakika muayene süresi Darbe-Yankı (Pulse-Echo) , Geçirim (ThroughTransmission), Tandem, S/R metodları 500 kHz (isteğe bağlı 100 kHz) to 20 MHz Azami 16 kanal Çalışma sıcaklığı 0-50°C Düşük güç harcama modu Equipment conform to EN12668 standard Ultrasonic examination possible from the axle head Compact and portable Industrial PC, industrial touch panel TFT display and industrial keyboard Advanced power management Simultaneous testing with up to 8 probes Moveable and flexible probe holder for accurate positioning Probe holders can be quickly and easily adapted to different axle types 360° rotation of each probe circularly around the axle head Build in coordinate interface Examination time max. 5 minutes Pulse-Echo, Through Transmission, Tandem, S/R methods 500 kHz (optional 100 kHz) to 20 MHz Up to 16 channels Operating ambient temperature shall be 050°C Low power consumption mode 9 10 Ultrasonik Donanım PCUS Pro - Ultrasonic Hardware PCUS Pro Bileşenler: US-Ön uç bileşenleri: Maksimum 8 kanal devre kartı 1 adet yüksek voltaj devre kartı Kullanıcı tanımlı arayüz için 1 adet kart yuvası 1 adet muhafaza 12 V Harici Güç Kaynağı USB 2.0 Endüstriyel PC (PCUS® Pro Mob) USB 2.0 arayüzü ile birlikte Components: US-Front end consists of: An external Power Supply USB2.0 cable An industrial PC (PCUS® Pro Mob) with a USB 2.0 interface Maximum of 8 channel circuit boards 1 high voltage circuit board 1 slot for user defined coordinate interface 1 housing 12 V 11 Genel Özellikler: Boyutlar (W x D x H): Çalışma sıcaklığı aralığı: Ağırlık: Güç Kaynağı: 165 mm (montaj tertibatı ile 190 mm) x 150 mm x 65 mm 0°C - 50°C 1.6 kg +12 V, maksimum 48 W (genellikle 30 W) General Characteristics: Dimensions (W x D x H): Temperature range: Weight: Power Supply 165 mm (190 mm including mounting) x 150 mm x 65 mm 0 to 50 °C 1.6 Kg +12 V, maximum 48 W (typically 30 W) Bağlantılar: Güç Kaynağı: USB 2.0-Bağlantı: Arama ünitesi bağlantısı: Tetikleyici girişi: Tetikleyici çıkışı: Bulgin Panel Jack PX0419 Bulgin Panel Jack PX0443 Lemo 00 Lemo 00 Lemo 00 12 Connections: Power Supply: USB 2.0-Connection: Search unit connections: Trigger input: Trigger output: Bulgin Panel Jack PX0419 Bulgin Panel Jack PX0443 Lemo 00 Lemo 00 Lemo 00 Harici Arayüz: Arayüz: Tetikleyici girişi: Tetikleyici çıkışı: USB 2.0 Yüksek Hız TTL, H- ya da L- aktif, darbe boyutu > 100 ns, galvanik olarak izoleli TTL, H- ya da L- active, darbe boyutu 200 ns, galvanik olarak izoleli External Interfaces: Interface: Trigger input: Trigger output: USB2.0 High Speed TTL, H-or L-active, impulse width > 100 ns, galvanically isolated TTL, H-or L-active, impulse width 200 ns, galvanically isolated Tarama Ünitesi Tutucu Sistemi Tarama Ünitesi Tutucu Sistemi Tarama ünitesi tutucu sistemi, aksın bitiş noktasına, aksa özgü adaptör halkaları aracılığla ve uygun bağlama vidaları ile monte edilmektedir. 8 farklı tarama ünitesi eş zamanlı olarak kullanılabilmektedir. Yansıma açısı, tarama ünitesinin yüzeyine monte edilen plastik saplamalar aracılığıyla her ünite için birbirinden bağımsız olarak ayarlanabilir. Problar, döner halkaya dirençli bir şekilde monte edilmiştir (Krank ve motor sürücülü versiyonları da opsiyonel olarak mevcuttur). Tarama ünitesinin optimum aks pozisyonuna ayarlanabilmesi için kodlayıcı (encoder) kullanılmaktadır. Tekerlek aksının ortasında yer alan eş merkezli halka yapısı sayesinde hassas muayene mümkün olmaktadır. The search unit holder system will be mounted on the axle’s end with appropriate fixing screws via axis-specific adapter rings. Up to 8 different search units can be used simultaneously. The angle of incidence can be set separately for each unit by mounting plastic wedges to the search unit’s surfaces. The probes are resiliently mounted on a rotating ring (crank and motor driven versions are optionally available) The encoder is used to align the search unit to the optimal axis position. The concentric ring structure is the middle of the wheel axle to allow precise examination. 13 Sistem Yapısı - System Architecture Ultrasonik tarama ünitesi (Ultrasonic search unit) İşlenmiş ultrasonic data Processed ultrasonic data Kodlayıcı (Encoder) Kontrol Paneli Veri üretimi sırasında, eş zamanlı olarak, During the data generation, simultaneous A- presentation of A-images for three selectable görüntülerinin ve dalga hatlarının görüntülerini search units and presentation of color-coded örtüştürme imkanı veren renk kodlu B-, TD ya B-, TD or C-images with the possibility to da C- görüntülerinin oluşturulması overlay images of the wave contour. seçilebilir Control Panel üç arama ünitesi için Veri üretimi boyunca tarama işlem durumunun Indication of scan progress during data generation bildirimi Bağlantı kontrolü Coupling control Veri üretiminin tamamlanmasından hemen Immediately after the completion of data sonra, hataları ve şekilleri ayırt edebilmek için generation, presentation of the test result in aks geometrisini bir araç olarak kullanacak form of a projection image (see images below) şekilde bütün test fonksiyonları için test for all test functions with an insertion of the sonuçlarının izdüşüm görüntüsü (aşağıdaki shaft geometry as a tool for distinguishing resimde görülebilir) şeklinde sunumu errors and shapes. Test verisi depolama dentim kanıtı Audit proof test data storage 14 Endüstriyel bilgisayar ve demonte vaziyetteki tarama sistemi (System with an industrial PC and disassembled search unit) Tekerlek Seti üzerine monte edilmiş tarama ünitesi tutucu sistemi (Search unit holder system mounted onto the wheelset) Sistem kalibrasyonu Özel kalibrasyon Test sonuçlarının kesinliği, güvenilirliği ve tekrar temini için yapay olarak sisteme tanıtılan ve kayıtlı test hatalarını içeren farklı referans aks modellerinin kullanımı Başarılı işlemlerin öncesinde ve sonrasında kalibrasyon sonuçlarının dökümantasyonu System calibration Special calibration Use of different reference axes with artificially introduced and documented test errors for checking the accuracy, reliability and reproducibility of the test results. Documentation of the calibration results before and after a successful test operation. Test Prensipleri Test Principle Position A Position B Position C Yazılım Software Muayene yazılımı, tekerlek grubu akslarının mekanize edilmiş ultrasonik muayene uygulamaları için geliştirilmiştir. PCUS elektronik ile kombinasyon halinde kullanılmaktadır. Yazılım, Microsoft Windows XP Professional SP3, Windows Vistan ve Windows 7 işletim sistemlerini desteklemektedir. The test software was developed for the implementation of mechanized ultrasonic testing of wheelset shafts. It is used in combination with the PCUS electronics. The software runs with the operating systems Microsoft Windows XP Professional SP3, Windows Vista and Windows 7. 15 Test Modu: Denetleyici kaydı Dalgaların ve tekerlek takımı karakteristiklerinin algılanması Tekerlek takımı aks çeşidi seçimi Test başlangıcı Standart test modunda test verisi üretimi Veri üretimi sırasında, eş zamanlı olarak, seçilebilir üç arama ünitesi için Agörüntülerinin ve dalga hatlarının görüntülerini örtüştürme imkanı veren renk kodlu B-, TD ya da C- görüntülerinin oluşturulması. Veri üretimi boyunca tarama işlem durumunun bildirimi Bağlama kontrolü Veri üretiminin tamamlanmasından hemen sonra, hataları ve şekilleri ayırt edebilmek için aks geometrisini bir araç olarak kullanacak şekilde bütün test fonksiyonları için test sonuçlarının izdüşüm görüntüsü (resimde görülebilir) şeklinde sunumu Test sonuçlarının 3D görüntülenmesi Test verisi depolama dentim kanıtı Test Mode: Registration of the inspector Detection of waves / wheelset characteristics Selection of wheelset shaft types Start of testing Test data generation in the standard test mode During the data generation, simultaneous presentation of A-images for three selectable search units and presentation of color-coded B-, TD or C-images with the possibility to overlay images of the wave contour. Indication of scan progress during data generation Coupling control Immediately after the completion of data generation, presentation of the test result in form of a projection image (see images below) for all test functions with an insertion of the shaft geometry as a tool for distinguishing errors and shapes. 3D Presentation of test results Audit proof test data storage 16 Avantajları Kısa muayene zamanı Hata tespiti için güvenilir ve tekrarlanabilir test sonuçları Kullanıcı odaklı yazılım sayesinde kolay kullanım Sistemin güvenilirliği Frauhofer Hasarsız Test Enstitüsü Dresden (Fraunhofer Institute for Nondestructive Testing Dresden) tarafından kontrol edilecektir Uzaktan bakım fonksiyonu ve entegre edilmiş kendi kendine teşhis özelliği aracılığı ile bakım desteği Test sonuçlarının hızlı bir şekilde belgelendirilmesi Farklı aks modelleri ve test ihtiyaçları için değiştirilebilen esnek yazılım A-,B- ve C- görüntülerinin ya da bireysel müşteri tanımlı ayrıntıların test verisi üretimi ve analizi Entegre edilmiş yönetim yazılımı (SATIRMS) ile hızlı ve anlaşılır bir şekilde düzenlenmiş durum göstergesi Modüler yapıya bağlı olarak yüksek esneklik Advantages Short inspection times Reliable, reproducible test results for flaw detection Easy to use via inspector-oriented software Reliability of the systems will be checked by the Fraunhofer Institute for Nondestructive Testing Dresden Maintenance support via integrated selfdiagnosis and remote maintenance function Immediate documentation of test results Software configuration of different types of axes and test requirements Test data processing and analysis of the A-, B- and C-images or of individual customer specifications Fast and clearly arranged status indication by integrated management software (SAT-IRMS) High flexibility due to the modular structure 17